Showing 1 – 7 of 7 resources

How controlled inoculation of sap tubing with Pseudomonadota strains may influence maple syrup quality

The study recently published in Canadian Journal of Microbiology and available in open access consisted in the inoculation of the sap collection system with three Pseudomonadota strains and to assess the microbial and organoleptic quality of maple sap and syrup (Gagnon et al., 2025). This work represents a significant step: rather than simply characterizing microbial communities, the study tested whether an intentional inoculation of selected bacterial strains into tubing systems can steer microbial succession and influence syrup quality.

Tapping Below the Lateral Line for a Sustainable Use of Maple Resource

In recent years, someproducers have seen the benefit of tapping maples below the lateral line for multiple reasons. The main reason is to access a larger area of healthy wood on the trunk. This is because the maple tree produces a compartmentalization zone inside the trunk following tapping, which isolates the wound left by the tap hole.

By opting for a tapping pattern that respects the necessary spacing of taps from year to year based on their size and number, the likelihood of tapping into compartmentalized wood is minimized. If, in addition, the tapping area is expanded by allowing tapping below the lateral line, the exploitation of the trunk surface is further optimized, ensuring the sustainability of sap collection.

A Promising Alternative to Defoamers for Maple Production

Foam development in the evaporator is a phenomenon often encountered in maple production (Martin, 2011). As it passes through the evaporator, the boiling sap can begin to foam quickly, especially at a later stage of the production season. When excessive foaming occurs, the use of a foam control agent, commonly called “antifoaming agent” or “defoamer” in the maple syrup industry, sometimes becomes necessary to avoid problematic overnows (low productivity, loss of product, cleaning challenges, safety, etc.).

Maple syrup production from sap preconcentrated to ultra high °Brix by membrane technology: Composition and properties

Maple syrup is produced typically from maple sap concentrated by nanofiltration or reverse osmosis at a moderate °Brix level ranging from 6 to 16 °Brix followed by heat evaporation. Recently, new membrane processes have been developed to concentrate maple sap to ultra-high °Brix reaching up to 40 °Brix. The aim of this study is to evaluate the effect of this ultra-high concentration of sap on the composition, the properties and the cost of corresponding maple syrup. Results showed some differences in chemical composition and properties between syrups produced from low and ultra-high concentration of sap. Syrups produced from ultra-high °Brix concentrated sap had lower concentrations of potassium and polyphenols, a lighter color and distinctive flavor. This was mainly observed when no modification were applied to the heating pattern in the evaporator pans. However, syrups produced by modulation of the heating pattern in the evaporator had color, flavor and taste similar to control syrups. These results demonstrate that syrups with comparable sensory properties can be obtained from low and ultra-high concentrated sap by adjusting the heating time depending on the initial °Brix. The concentration process to ultra high °Brix allows for a concomitant reduction of the production costs and a modulation of syrup quality.

Chemical composition and properties of maple sap treated with an ultra high membrane concentration process

Nanofiltration and Reverse Osmosis are membrane concentration processes originally used by maple syrup producers to preconcentrate the sap to a moderate °Brix level (8–16 °Brix). The purpose of this study is to evaluate the potential of new membrane technology to concentrate maple sap to ultra-high °Brix and to investigate the effect of this concentration on the chemical composition and physical properties of final sap concentrate. Maple sap was concentrated up to 42 °Brix using two industrial membrane units. The contents of main solutes increased with the °Brix of concentrates depending on the specific rejection rate of the membranes tested. A slight and significant decrease was observed in the availability of some solutes such as K+, Mn++ and polyphenols in ultra-high-concentrated sap. However, the apparent organoleptic and physical properties of these concentrates have not been altered. According to the results of this, the new membrane process allows to produce ultra-high °Brix concentrate of maple sap with interesting properties. However, further works have to be performed on this technology to more precisely determine the highest °Brix level that will minimise the affect on chemical composition and properties of concentrated sap and the corresponding maple syrup.

Effect of the new high vacuum technology on the chemical composition of maple sap and syrup

Techniques used to produce maple syrup have considerably evolved over the last decades making them more efficient and economically profitable. However, these advances must respect composition and quality standards as well as authenticity of maple products. Recently, a new and improved high vacuum technology has been made available to producers to achieve higher sap yields. The aim of the present study was therefore to evaluate the effect of this new system on the yield of sap and on the sap and syrup chemical composition.